July 28, 2019
You want Fry's with that?
With the cooling issue all taken care of (almost), I had one other computer issue to deal with with Himawari. When reading Facebook, I have a tendency to control-click lots of notifications to open them all in new tabs. But frequently that would lead to a random blue screen of death. Now, I had found a nifty utility that would comb through the mini-dumps and tell you want they were (BlueScreenView), but they were all over the place. The fact that they always occurred during heavy Facebook use, and it happened across two different browsers was confusing. Plus it didn't happen when I was using Etna. So it dawned on me that there might be something off with my hardware, not my software.
Enter Memtest.org. I ran MemTest86 overnight, and I got errors. So I ran them another night with just one DIMM in, and got errors. The next day while I was at work, I tested the other one. That one was clean. Running with just the one DIMM was okay, but a bit cramped. So this weekend's shopping included a run down to Fry's to get another 8 Gig stick. It was only $32.
While I was there I also grabbed a Silenx 120 mm fan. With all of the cooling moved outside the case, there wasn't anything but the very slow oversized fan that gently wafts over the drive bay moving any air inside the case. I had left the case open for a long time so I could watch the LED on the old Antec cooler, but that wasn't necessary any more. So when I buttoned up the case again, the video card started getting warm. (59 degrees C vs. 50 when open). I got this data from a monitoring program for my Corsair power supply I was finally able to run now that the internal USB header the Antec cooler hogged up was free for the usb cable that came with the power supply. (Those headers are two ports. I was going to make a splitter cable at some point, but that's no longer needed.) So while I was at Fry's, I grabbed the fan. It was hard to find something that didn't have multicolor LEDs in it for the casemod crowd. This one did have a little thermocouple hanging off of it to further moderate its speed and make it run even quieter. The fan definitely lives up to its name. It says it's <15 db, and I believe it. If they made a 4-pin model I'd consider changing out the fans on the radiator. And now, with the case closed up, the video card is running down at 48 Celsius.
I also grabbed another cheap 32 gig USB thumb drive. A long time ago I was able to get a USB card for my old Mac. It seemed like it would be a cheap way to back up the drive I've got left. Kind of a closing the barn after the horses burn it down.... It's been a bit trying since the thumb drive is DOS formatted, but the Mac has a way of putting its dual fork files on it that seems to be working. Biggest problem so far is file names with /'s in them, since they're legal on the Mac and not on DOS. Transfers are slow as heck, and figuring out where the occasional mismatches are coming from is not fun. But if I can get that squared away, and the freezer trick works on the dead drive, maybe I can save things.
Now I'm just struggling with Macrium to make a clone of my boot drive that is actually bootable. That backup is long ovedue. I had a malware scare with a fan control program I downloaded, which fortunately amounted to nothing, but then again, if the system is going to be stable again with the new ram, maybe manually setting the fan config after a boot won't be that big of a deal. I wanted to have a bootable scratch drive to test the fan program with. But an updated backup would be nice to have.
Oh, as for the title. Fry's itself, once a pinnacle of Electronics and Computer stores, had just been getting more and more depressing every time I visit, with more empty shelves and less selection than ever. And the things they do have in stock are just... odd.... Lots of things you never knew you never needed. And all the cute Asian girls are long gone. Even the surly Indian women are gone. The remaining staff, well, at least they seemed knowledgeable, but they were the final Rejects of Retailing - from "Middle-aged bodymod girl", to Mr. "We carry them but we don't have any", to "Guess my pronouns." The whole experience felt like they've been holding out on having their going out of business sale because the rest of the economy is so good, but they haven't been getting a piece of it.
Posted by: Mauser at
12:56 AM
| Comments (1)
| Add Comment
Post contains 837 words, total size 5 kb.
July 25, 2019
Ani-nouto is down
Any news?
Posted by: Mauser at
06:23 PM
| Comments (3)
| Add Comment
Post contains 5 words, total size 1 kb.
July 20, 2019
Seemed like a good time for this
Posted by: Mauser at
09:00 AM
| No Comments
| Add Comment
Post contains 7 words, total size 1 kb.
July 06, 2019
Losing my cool
Seems to be my month for computer problems. First an ancient hard drive on the equally ancient Mac, and now my hybrid cooling system on my PC is down. I kinda knew something was coming, it was running slightly hot, but it went down fast. And of course, I never bothered to get the parts I wanted to redo the things left from the original canned system. Fortunately I have Etna, and ordered them from Amazon, but it's gonna be a few days without access to Himawari.
I was playing WoWS when I overheated and shut down. I tried changing out the water, but I realized it wasn't pumping, even though the pump worked. I drained the system and took parts apart, and I couldn't blow through it. I even tried my vacuum pump, and it actually held a vacuum for a few seconds, so it definitely wasn't flowing water. I mean, it could move SOME water, but my pump wasn't up to it. So I've got a new radiator and CPU block on order, and they use full sized tubing, as opposed to the skinny Antec original, so it should cool a lot better, but I'll have to do something else for the automatic fan speed control (I think the motherboard can do it) and I won't have color-coded LEDs telling me the water temperature.
7/13/19 Update! Done! I did have a few minor obstacles. The radiator was tapped to 4-40 (I think) before being painted, so I had to buy a new tap in order to clean out the holes and make damned sure they were 4-40. I also had to buy various lengths of 4-40 screws to hold the fans on it.
The biggest issue was soldering up a Y- cable to drive both fans. I started with the Y-cable that came from the Antec CPU block, but that was soldered to the control board. However I dug through a junk box and found the original air/fan heat sink that came with the processor and snipped off the connector and soldered the wires together. (I'd've preferred to crimp the connectors, but I didn't have any of the right kind of terminals.)
I also knocked out that wooden box thing to put the reservoir at the highest point, and the pump under it. Swung by Grainger for a fat tube of heat transfer grease ($4.50, more than I will ever need, and cheaper per gram than the tiny syringes you can get at Fry's).
While I was at it, I tore apart the Antec system to see if I could figure where the blockage was. Simply enough, it was the CPU block. It was made with paper-thin fins of copper spaced about a paper's thickness apart, and the enclosure forced the flow only though those fins. That was the source of all the resistance (so I saved the radiator to rest in a junk box for who knows what project in the future).
Once I decided how it was all going to go together, I ran all new tubing, filled it with water (less than I thought it would take), and fired it up. There was only a small drip at the CPU block that went away with a little tightening, and when I powered it up, WHOA! That poor pump that had been laboring against that restriction cut loose like nobody's business. The flow is amazing.
7/13/19 Update! Done! I did have a few minor obstacles. The radiator was tapped to 4-40 (I think) before being painted, so I had to buy a new tap in order to clean out the holes and make damned sure they were 4-40. I also had to buy various lengths of 4-40 screws to hold the fans on it.
The biggest issue was soldering up a Y- cable to drive both fans. I started with the Y-cable that came from the Antec CPU block, but that was soldered to the control board. However I dug through a junk box and found the original air/fan heat sink that came with the processor and snipped off the connector and soldered the wires together. (I'd've preferred to crimp the connectors, but I didn't have any of the right kind of terminals.)
I also knocked out that wooden box thing to put the reservoir at the highest point, and the pump under it. Swung by Grainger for a fat tube of heat transfer grease ($4.50, more than I will ever need, and cheaper per gram than the tiny syringes you can get at Fry's).
While I was at it, I tore apart the Antec system to see if I could figure where the blockage was. Simply enough, it was the CPU block. It was made with paper-thin fins of copper spaced about a paper's thickness apart, and the enclosure forced the flow only though those fins. That was the source of all the resistance (so I saved the radiator to rest in a junk box for who knows what project in the future).
Once I decided how it was all going to go together, I ran all new tubing, filled it with water (less than I thought it would take), and fired it up. There was only a small drip at the CPU block that went away with a little tightening, and when I powered it up, WHOA! That poor pump that had been laboring against that restriction cut loose like nobody's business. The flow is amazing.
The fans also ran at top speed since the CPU Fan connector was set to 100% when the speed was moderated by the Antec CPU Block. Fortunately, the BIOS has a setting to moderate the fan based on a target CPU temp. Unfortunately, the BIOS setting won't go below 50%, which is still too loud and too fast. Fortunately, one of the utilities, MSI Control Center, will let you set cooling rules as low as 20%. Unfortunately you have to run it and reload the profile every time you reboot. Ah well, it's still way quiet, and a lot cooler. Running at 41 °C as I type this.
Posted by: Mauser at
09:46 PM
| Comments (5)
| Add Comment
Post contains 683 words, total size 5 kb.
June 23, 2019
New post on my writing blog
New post on my writing blog... but it's not SF?
What a long Strange Trip it's Been
Posted by: Mauser at
12:15 PM
| No Comments
| Add Comment
Post contains 23 words, total size 1 kb.
June 13, 2019
Because I love you guys, even if you don't comment
Posted by: Mauser at
06:19 PM
| Comments (1)
| Add Comment
Post contains 13 words, total size 1 kb.
June 09, 2019
Sewayaki Kitsune no Senko-san
Or The Helpful Fox Senko-san.
Is this a healing anime? Kuroto Nakano is a severely overworked Salaryman. No wife, no kids, just the minimal apartment that he barely even gets to sleep in. This has understandably worn him out, and a cloud of gloom is hovering over him. The fox goddess sees this (Apparently there's an ancient connection between his family and the Kitsunes), and Senko volunteers for the duty to help him make his life better and more relaxed, because that gloom isactually a kind of threat.
Now Senko is an adorable little 800-year-old fox spirit, and she's dressed very traditionally in a Kimono and Geta, and her experience with the modern world is minimal. So it takes a little while for her to settle in to things (She cooks for him using her foxfire because she didn't know how to work the gas.) Her battles with the household machinery also attract the attention of the female Mangaka next door, who was used to the silence coming from Nakano's usually empty apartment. But after Senko whips up a meal for her, any thoughts of going to the police evaporate.
Despite all her best efforts, Nakano is still beaten down. But a bit better. He really does enjoy fluffing Senko's tail, and she puts up with that indignity because it does, after all, make him happy.
Senko does, however, have a rival up in heaven. Shiro is a much more modern Kitsune, who wears a high-slit dress, long gloves and thigh highs, and she thinks Senko is not doing nearly enough to reduce Nakano's stress, so she decides to join the party. She is naturally Senko's opposite, where Senko is humble, Shiro is egotistical. Where Senko wants to serve Nakano, Shiro wants him to serve her (All of those who serve her look happy, she explains).
I've only gotten to episode 5 of the 9 out so far from Erai-raws (Wish they'd translate the songs). But it's a cute little inoffensive show. Nobody's going to rage over it like The Rising of the Shield Hero.
Posted by: Mauser at
08:32 AM
| Comments (2)
| Add Comment
Post contains 355 words, total size 3 kb.
May 15, 2019
Ugh,
FINALLY finished plowing my way through Persona 4. What a slog. I'm still not entirely sure why I did it. Persona 5 came out, and someone posted a segment of it on Twitter that made me curious, and my stupid completist urge made me seek out earlier series. 26 episodes is what it took. A huge number of repetitive episodes introducing each character of the large cast as they confront their innermost urges and gain their powers, a brief and disappointing battle against a false bad guy, a second season crammed FULL of filler, then improbably another false villain, a fake death of a little girl, and the real villain.
Well, I just found Persona 3, seems to be a very different series. Four movies. Maybe I'll eventually get around to the series that piqued my interest.
OTOH, I watch every episode of The Rise of the Shield Hero as it arrives. There is no queue. Very much worth it.
Well, I just found Persona 3, seems to be a very different series. Four movies. Maybe I'll eventually get around to the series that piqued my interest.
OTOH, I watch every episode of The Rise of the Shield Hero as it arrives. There is no queue. Very much worth it.
Posted by: Mauser at
08:14 PM
| No Comments
| Add Comment
Post contains 161 words, total size 1 kb.
April 06, 2019
Spring season is starting
What are you all watching?
AnimeChart
AnimeChart
Posted by: Mauser at
10:33 AM
| Comments (2)
| Add Comment
Post contains 10 words, total size 1 kb.
March 24, 2019
Just being silly
Posted by: Mauser at
02:48 PM
| Comments (2)
| Add Comment
Post contains 6 words, total size 1 kb.
47kb generated in CPU 0.0671, elapsed 0.1486 seconds.
36 queries taking 0.1323 seconds, 235 records returned.
Powered by Minx 1.1.6c-pink.
36 queries taking 0.1323 seconds, 235 records returned.
Powered by Minx 1.1.6c-pink.
